“I love the focus on both a healthy home and helping the individuals inside the home get healthy. I loved that Bryce took the time to educate as we went through the whole process.”
Drywall, insulation and carpet pad stay wet long after the floor looks dry, and mold follows a flood or a burst pipe into them.
Water damage mold removal in Falls Church depends on how long the house stayed wet after a burst pipe, an overflowing appliance or a creek over its banks. A supply line behind the washer and a flooded creek soak the same materials, from drywall and insulation to the subfloor and the framing at the bottom of the walls.
Treatment comes once the water has stopped and the house is drying.
For the whole-house view, start with our mold remediation page.
5.0/5 stars on Google. Every review here is quoted word for word from Google. Read them all on our reviews page.
“I love the focus on both a healthy home and helping the individuals inside the home get healthy. I loved that Bryce took the time to educate as we went through the whole process.”
“Pure Maintenance is fantastic. Bryce is exceptional—he is an encyclopedia of information and, to top it off, he has the most caring heart. He is absolutely outstanding—extraordinarily knowledgeable, professional, detail-oriented, and responsive. He is serious both about the work and about making sure his clients feel better and are well taken care of. The whole team (Bryce, Ron, James, etc.) all stepped in to help us when we were in dire need and repeatedly gave us hope whenever we encountered a challenge that made us feel hopeless. On a scale of 100, I would give a rating of a million. Pure Maintenance epitomizes what the heart and purpose of every company should be. If all companies were like Pure Maintenance, there would never be a negative review. We are beyond grateful.”
“I see why Pure Maintenance is highly rated and approved by Home Advisor. Mold can be dangerous, especially for those with respiratory issues. Pure Maintenance are experienced professionals in mold that care about the health of their clients.”
“Bryce Rogers the owner came to inspect for potential mold in the upstairs kitchen. He found no evidence of mold but checked the humidity levels which were a bit high. He was very friendly, knowledgeable and helpful in providing quick tips to prevent moisture and humidity. Since he was already here I asked him to check the downstairs living area which has not been used for most of the summer. The humidity was even higher downstairs and there were visible signs of mold in the kitchen area. We decided to have the dry fogging process done to kill the mold and improve the air quality. Bryce was very professional as was his team who performed the service. Bryce responds quickly, provides valued information about the process as well as a follow up which includes a plan to reduce humidity. The service was reasonable and there is a big difference in the quality of the air in the entire house. I give his company Pure Maintenance a well deserved 5 stars.”
“Bryce promptly made an appointment on-site to review our needs and immediately followed up with a quote as well as several technical materials to address our many questions about the efficacy and safety of dry fog mold removal. He patiently answered all our questions and was flexible regarding the scheduling of our project over two days. On the second day, he called to let us know he'd be 30 minutes late. He was very conscientious about meeting schedules and setting accurate expectations. His team was pleasant to work with and extremely considerate during the entire time they were working on our project. It was a pleasure to work with Pure Maintenance DC -- they exceeded our expectations on all counts. About our job: We had a lot of mold on dry wall in bathrooms and around windows that leaked. We have an indoor tennis court with an unusually high ceiling. Now, about a week later, it seems to have worked extremely well. We can tell the difference in the air after the treatment. Bottom line, we would highly recommend Pure Maintenance DC to anyone with a mold problem. Dry fogging has proved to be an excellent solution for us.”
“When we discovered mold in our basement we started looking for the best company to help us. Thank goodness we found the Washington DC-area Pure Maintenance office. They were highly responsive and professional from their very first reply to our inquiry, then throughout the process of assessing our problem, recommending a solution, doing the work as agreed, and providing test results to confirm success. Their dry-fog method is cutting edge, treating our entire townhouse successfully in just a few hours. And they charged us even less than quoted, choosing to err on the conservative side in calculating the size of our home. Highly recommended!”
Pimmit Run meets the Potomac at Chain Bridge. The stretch beside Pimmit Hills was widened and lined with concrete in the early 1970s to hold back flooding.
If creek water reached your basement or crawl space, note how high it came and take photos before you clean up. The wet line on the drywall or the block tells us how far up to take moisture readings, and the photos show what the water touched. Creek water also leaves silt on floors and in the bottom of wall cavities, and wet silt holds moisture against the wood after the water drains away.
Stop the water, then dry the house. Moisture mapping shows which rooms are still wet, down to the wood plate at the bottom of each wall, which is often the last part to dry.
Rooms dry at different speeds. A closed room with no air moving through it stays wet long after one with fans running, so the readings set the treatment date room by room. Closets, cabinets and the space under the stairs are usually the slowest.
Mold can appear weeks after the water is gone if something stayed wet. A gray line along the bottom of a wall, spotting on baseboards, flooring that starts to cup or lift, or a musty smell when the HVAC runs can be the first sign.
Water also travels sideways inside a house. A burst pipe in a second-floor bathroom can wet the ceiling, wall cavities and subfloor of the rooms below and beside it, so we map the rooms around the obvious one as well.
If repairs are about to close a wall back up, have it checked first, because new drywall and flooring put the materials behind them out of reach. Baseboards pulled off for drying leave a good spot for a reading before they go back on.
The water source has to be fixed first, by you or the right trade, because mold comes back wherever moisture keeps arriving. On treatment day the home is empty: people, pets and plants leave, and furniture and electronics generally stay where they are.
The VaPURE sterilant goes in as a vapor and reaches surfaces, wall cavities, HVAC ducting, porous materials and the air. An antimicrobial protectant stage follows, which helps resist new growth once the moisture cause is fixed. Most homes are treated in a single day, and families are back the same evening.
Most homes need no demolition. When a material is too far gone, we say so in the estimate and it comes out. Afterward, air samples go to the same accredited third-party lab, which has no affiliation with EnviroPure.
When the whole property is treated and a follow-up lab test within a year shows mold above regional averages, we re-treat at no charge.
The consultation and visual inspection are free, and when the inspection confirms visible mold, you get an estimate.
See how this work connects to every other part of mold remediation in our area.
As soon as the source is stopped. Call us and we'll talk through next steps and the earliest visit we can offer.
The process is the same. Moisture mapping shows whether the materials have dried or are still wet, which also tells us whether the source was really fixed, and treatment covers growth that formed in the meantime.
The source decides who you call: a plumber for a pipe, and for flooding, whoever handles the grading, gutters or drainage around the house.
Lift wet rugs and loose mats right away. Leave glued-down or nailed flooring in place until the moisture readings show how far the water went.
Tell us what you're seeing and where. We'll explain the likely next step and what it would involve, including EnviroPure services, availability and pricing.
Homes in Oakton, Springfield, Great Falls and Fairfax get the same VaPURE process and the same lab testing as homes in Falls Church, and so do homes in Alexandria and in Bethesda, Chevy Chase and Potomac, MD. Ask us about your street.
Falls Church · McLean · Vienna · Tysons · Great Falls · Oakton · Annandale · Springfield · Fairfax
Alexandria · Old Town Alexandria · Kingstowne
Bethesda · Potomac · Chevy Chase